CMX DPX-6L

CMX (quote good 4/20/15)$36000.00 LESS 10% (Take off $1000 for non-jacketed mix can) QUOTE GOOD FOR 90 DAYSF.O.B. - BOHEMIA NYPROPOSAL PREPARED FOR: Arnold Equipment for MesocoatDATE: May 15 2014COVERING:One (1) CMX Laboratory Double Planetary Mixer Model DPX-6L. Unit has a recommended working capacity of 6 liters (1.5 gallons) and a full holding capacity of 8 liters (2 gallons). Unit includes the following features and specifications:CONFIGURATION & COVER LIFTING SYSTEM: Removable-Vessel design configured for use with multiple mixing vessels. Compressed Air / Oil hydraulic lifting system with two-hand operation raise / lower controls to raise and lower vacuum hood and agitators from the vessel (80 - 90 psig compressed air required). Limit switches to prevent operation of agitator drive when the vacuum hood is lifted from mixing vessel or when the mixing vessel is removed from the mixing position.MATERIALS OF CONSTRUCTION & FINISHES: All product contact parts including agitators inside of vessel and inside of vacuum hood to be type 304 stainless steel polished to a surface finish roughness average (Ra) < 0.8 um (~80 grit). All non-stainless steel exterior surfaces are coated with Safety Orange chemical-resistant two-part coating. All elastomers (including mechanical seal O-rings) to be FDA approved Viton. Exterior of vessel and vacuum hood to be polished to a surface finish roughness average (Ra) < 0.8 um (~80 grit).OPERATIONAL PARAMETERS: Unit designed for operation under full vacuum up to 29.5 Hg (-1 BarG).AGITATION SYSTEM:Agitation system for mixing high viscosity formulations consists of two (2) planetary stirrer blades that rotate on their own axes while revolving around a common central axis. Includes the following: Variable speed planetary stirrers driven by a 2 HP TEFC inverter-duty motor suitable for 3 phase 60 Hz 600 volt input for an orbital speed range of 5 to 100 RPM and stirrer blades on their own axes between 6 and 120 RPM. Variable speed is accomplished through the use of an AC variable frequency inverter drive. Stainless steel type 304 heavy-duty gearbox housing with special gearing capped gasketed & sealed. Stainless steel sleeve bearing. Underside of bonnet above vacuum hood is fabricated of stainless steel. Type 304 stainless steel rectangular stirrers and stirrer shafts. Stirrer blades polished to a surface finish roughness average (Ra) < 0.8 um (~80 grit).REMOVABLE VACUUM MIXING VESSEL:Stainless steel type 304 removable vacuum vessel with flat bottom to include the following: Interior and exterior of vessel polished to a surface finish roughness average (Ra) < 0.8 um (~80 grit). Two (2) stainless steel handle attached to the front exterior of the mixing vessel.VACUUM HOOD:Stainless steel type 304 vacuum hood to include the following: Two (2) 3 diameter combination sight and charge ports with Pyrex glass Viton gasket and sanitary clamp. One (1) ½ half- coupling with vacuum gauge. One (1) ½ half- coupling vacuum port with valve. Interior and exterior of vacuum/pressure cover polished to a surface finish roughness average (Ra) < 0.8 um (~80 grit).CONTROL SYSTEM:NEMA 12 Control System. Panel is pre-wired and mounted to mixer and suitable for single point connection to your power source. One (1) Illuminated Start Momentary Push-button (green) for the agitators. One (1) Stop Momentary Push-buttons (red) for the agitators. One (1) 2 HP Variable Frequency Drive internally mounted. One (1) Speed potentiometer for Variable Speed Control of the agitators. Digital tachometer. Digital ammeter. Emergency Stop pushbutton. Relays for two limit switches wired normally closed. Circuit protection wire fuses terminal blocks etc. Rotary disconnect.Input Voltage: 600 volt 3 phase 60 Hz. PRICE F.O.B. BOHEMIA NY:……………………………..…….…………...$35000.00SHIPMENT: 16 - 18 weeks after receipt of order and down payment.TERMS: 50% down payment with order balance net 30 days from shipment.