CMX DPX-400L

CMX PROCESS TECHNOLOGIES (PRICED 5/5/15)MIXER $190000.00 LESS 10% DISCHARGE $69500 LESS 10%CONTACT DOUG COHEN FORMORE INFORMATION DATE: September 17 2014COVERING:One (1) CMX Double Planetary Mixer Model DPX-400L. Unit has a recommended maximum working capacity of 380 liters (100 gallons) and a full holding capacity of 435 liters (115 gallons). Unit includes the following features and specifications: CONFIGURATION & COVER LIFTING SYSTEM: Removable-Vessel design configured for use with multiple mixing vessels. Compressed Air / Oil hydraulic lifting system with two-hand operation raise / lower controls to raise and lower vacuum hood and agitators from the vessel (80 - 90 psig compressed air required). Limit switches to prevent operation of agitator drive when the vacuum hood is lifted from mixing vessel or when the mixing vessel is removed from the mixing position.MATERIALS OF CONSTRUCTION & FINISHES: All product contact parts including agitators inside of vessel and inside of vacuum hood to be type 304 stainless steel polished to a surface finish roughness average (Ra) < 0.8 um (~80 grit). All non-stainless steel exterior surfaces are coated with Safety Orange chemical-resistant two-part coating. All elastomers (including mechanical seal O-rings) to be FDA approved Viton. Exterior of vessel and vacuum hood to be polished to a surface finish roughness average (Ra) < 0.8 um (~80 grit).OPERATIONAL PARAMETERS: Unit designed for operation under full vacuum up to 29.5 Hg (-1 BarG).AGITATION SYSTEM: Agitation system for mixing high viscosity formulations consists of two (2) planetary stirrer blades that rotate on their own axes while revolving around a common central axis. Includes the following: Variable speed planetary stirrers driven by a 30 HP TEFC inverter-duty motor suitable for 3 phase 60 Hz 460 volt input for an orbital speed range of 8 to 30 RPM and stirrer blades on their own axes between 9 and 34 RPM. Heavy-duty type 304 cast stainless steel gearbox housing with special gearing capped gasketed & sealed. Pre-drilled for addition of sidewall scraper arm. Exterior polished to a surface finish roughness average (Ra) < 0.8 um (~80 grit). Variable speed is accomplished through the use of an AC variable frequency inverter drive. Stainless steel steel sleeve bearing. Underside of bonnet above vacuum hood is fabricated of stainless steel. Type 304 stainless steel rectangular stirrers and stirrer shafts. Stirrer blades polished to a surface finish roughness average (Ra) < 0.8 um (~80 grit). Special mechanical seals on stirrer shafts mounted in stainless steel carriers. REMOVABLE VACUUM MIXING VESSEL:Stainless steel type 304 removable vacuum vessel with flat bottom to include the following: 2 Flush Tank Ball Valve with 2 NPT threaded outlet connection. Carbon steel jacket on the sides and bottom rated for 50 psig. Two (2) fixed and two (2) swivel caster wheels. Interior and exterior of vessel polished to a surface finish roughness average (Ra) < 0.8 um (~80 grit). Flush-mounted thermocouple or RTD in the vessel sidewall. Two (2) stainless steel lift trunnions attached to the side exterior of the mixing vessel. One (1) stainless steel handle attached to the front exterior of the mixing vessel.VACUUM HOOD:Stainless steel type 304 vacuum hood to include the following: Two (2) 3 diameter combination sight and charge ports with Pyrex glass Viton gasket and sanitary clamp. One (1) ½ half- coupling with vacuum gauge. One (1) ½ half- coupling vacuum port with valve. Interior and exterior of vacuum/pressure cover polished to a surface finish roughness average (Ra) < 0.8 um (~80 grit).CONTROL SYSTEM (EXPLOSION PROOF CLASS I DIV. 1):Control system suitable for 460 volt 3 phase 60 Hz input consists of a local explosion proof operator station and a remote drive panel for mounting outside of the hazardous classified area includes:Local XP Operator Station:One (1) cast aluminum NEMA 7&9 Local Explosion Proof Operator Station suitable for Class I Div. 1 environments including: Start / Stop pushbuttons. Speed control potentiometer. Digital tachometer. Digital ammeter. One (1) digital product temperature readout. E-Stop pushbutton.Remote Drive Panel:One (1) NEMA 12 powder-coated steel enclosure for mounting outside of the hazardous area with the following: One (1) 30 HP 460 volt 3 phase variable frequency drive. Fused disconnect with Lockable handle disconnect. Intrinsically safe barriers as needed. PRICE F.O.B. BOHEMIA NY:……………………………..……………....$190000.00SHIPMENT: 14 - 16 weeks after receipt of order and down payment.TERMS: 50% down payment with order balance net 30 days from shipment.OPTIONELEVATOR-STYLE DISCHARGE (EXTRUDER) SYSTEM: One (1) Elevator-Style Discharge System Model DSF800 for use with 100 Gallon vessels: Heavy duty carbon steel support structure finished with a two-component epoxy paint. Platen with type 304 stainless steel wetted parts and Viton sealing O-ring. Hydraulic elevator-type lifting arrangement to raise mixing vessel to desired discharge height including automatic locking system for the vessel support. Platen and elevator lifting arrangement is activated by means of a self-contained tandem hydraulic power unit driven by a 7.5 kW 480 volt 3 phase 60 cycle TEFC motor. Pressure compensating hydraulic power unit with water-cooled heat exchanger for extended discharge periods. Safety device with movable gate. Controls mounted to the side of the Discharge System for actuation of the platen and the elevator system. PRICE:……………………………..………………………….……….………...$69500.00 ORDERING INFORMATION:Any orders resulting from this proposal should be made out to:CMX Process Technologies373 Nesconset HighwaySuite 116Hauppauge NY 11788